DuraSteel24x18 NSF Stainless Steel Cart - Heavy Duty Rolling Food Prep Table with Undershelf - Metal Utility Cart for Commercial Restaurant Kitchen, Laundry, Side Mixer Stand

Went together easily, no dents or scratches, great casters that don't leave a mark on my nice hardwood floors... This thing is absolutely rock solid quality, and fits my Ooni Volt pizza oven perfectly. Big thumbs up!If you need hooks to hold your peels and such, the "MIKEDE Magnetic Hooks, 70LB+ Swivel" 4-pack of hooks work perfectly. They don't slide at all.

The media could not be loaded. The unit is an INDOOR DuraSteel 18 in x 30 in SS top kitchen work mini island with casters. Kitchen is tight, so I needed an extra work surface and more storage. With the purchase of an extra DuraSteel shelf I was able to stably support/wedge in the added VEVOR SS 2-drawer unit. No hardware required. The unit specs are 17.8" W x 20.2" H x 12.2" D. It still left me the bottom (original) shelf, for more storage. BTW, the extra DuraSteel shelf runs only $33/from "returns". The VEVOR unit does leave some back and side space unused - it is 12.7 in to the units' 18 in depth. Not a big deal. You will notice that I placed the VEVOR unit off center. That is because I plan to "close off" the end gap in some manner to slot in a wooden chopping block. The drawers slide in & out smoothly, because of ball bearing hardware. BTW, I feel that the 18 in x 30 in DuraSteel top dimensions are an absolute minimum for a functional area to perform most kitchen tasks. Also, wheels are a must in a small kitchen. The unit is topped off with a Winco CBWT-1830 Cutting Board, 18-Inch by 30-Inch by 1/2-Inch. It fits great but slides on top of the SS top surface. My solution: DIYMAG Neodymium "finger" magnets as seen in the pics (left). These are super strong yet can be removed. They do stick to this SS surface to contain movement of the board.*** Feb. 24, 2025. I just modified the unit by organizing the "empty" space below the table top [around the added VEVOR drawer unit] via 2 sets of DuraSteel OPEN Work Table BASE Bracing. This is not the intended use by the manufacturer. This move required me to take off the top. HINT: DO NOT over tighten the horizontal sections until all are installed and checked for level. Really paid off. On one side I safely store cutting boards. On another I hang basic kitchen gadgets with SS hooks. And the back cradles a long rolling pin...

Very nice little table. very sturdy, rolls nice. Yes it will take you a bit to get the protective plastic film off but just take your time.

Great Instructions given. Easy to put together. Wheels were purchase separately.

I bought this to use on my lanai with a portable pizza oven. No surprise that there's some assembly required, so while unpacking the top shelf, I noticed was how thin the stainless steel was. I don't expect this to be a problem supporting the weight of my oven (45 lbs). I also noticed how easily the stainless steel scratches. This for me isn't a big deal since I don't care about a few scratches on an outdoor table.Next I started assembly. First you slide the legs into the bottom shelf. You need to use a guide or ruler to get each leg in the same amount as there are no markings for guidance. There are two hex set screws on each sleeve to grip the leg and lock it in place. Next you insert the tops of the legs into the top shelf. Here's where I noticed the biggest problem. The spacing of the top shelf leg holders were about an inch further apart than the spacing on the lower shelf. I'm not sure if the leg holder supports are glued or welded in, looks like glue to me but I could be wrong. In any case, a little more careful measuring at the factory would be nice. Luckily the lower shelf sleeves have enough play so the legs can be angled enough to fit into the top shelf sleeves. It required two people and a decent amount of pressure. After tightening the set screws to lock in the top shelf, its time to install the casters (if your version includes them). I called the manufacturer to confirm how to remove the installed leg ends and install the expansion sleeve casters. Kudos to them for quickly answering the phone. They recommended a flat bladed screwdriver to pry the plastic leg ends from the legs. I found that a plumbers wrench was an easier method - gripping and twisting the plastic leg inserts removes them easily. The casters are very heavy duty and easy to install and lock in place.BTW, the actual height of the cart with the casters is 37-3/4", not 34". This was annoying to me as I have it next to another cart that is 34" including it's casters.Overall though, the cart meets my needs and is reasonable quality for the price.

The media could not be loaded. Got this cart after trying the vevor cart of the same size from Amazon. A perfect fit for medium harvest right freeze dryer this is table is rock solid with it on there. Rolls smoothly, does not flex or twist with around 150lbs on it. The vevor was so shaky, unstable and flexing I didn't trust it with 10lbs let alone the freeze dryer.Could not be happier with this cart, solid, better and thicker stainless and much better casters. Its more than the vevor but do not think twice, you will regret it if you go with the cheaper tables on Amazon!