MZS Motorcycle Tail Light LED Integrated Turn Signal Blinker Smoke Compatible with GSXR600 GSXR 600 2008-2016 / GSXR750 GSXR 750 2008-2016 / GSXR1000 GSXR 1000 2009-2013

Installed easily, looks much better than stock, lights up bright enough to see during the day, functions exactly as it should, I've put about a thousand miles on it and so far no complaints

came with good instructions and was plug and play

It looks great and works but I had to file down the top edge on both sides as it was rubbing on the fairing and scratching the paint. I also added some washers on the mounting hardware to push it out a bit to keep it from rubbing. It actually scratched the paint on the rear fairing pretty bad but I was getting it resprayed anyways so luckily I mounted this before the paint was scheduled.I’d give it five stars if it fit better. You’ll be doing a little filing before you install it or you’ll scratch up the back of the bike. This was on my 2017 ZX14R

Works very good and fit perfectly

I was pretty skeptical about getting a tail light this cheap, but it's actually not that bad. Definitely not the best tail light I've seen, but for the price, its absolutely exceptional. I would expect this level of quality from a tail Light double the price. The only thing that may change my mind is durability. But for this price point($45) I would be happy if it only lasted 2 years. Btw This is on my 2015 fz07. It fit absolutely perfectly. It is exactly like the oem one, nothing needed to be modified.You do have to cut and spice wires for the install. It does not come with the connectors to just plug and play. You also have to switch over some rubber Grommets from your old taillight into this new one. If you know what you're doing , it takes twenty minutes. if you've never worked on a bike before , it might take you 2-3 hours. I wouldDo all the wiring first, then turn the Ignition on and check that all the lights are functioning properly and then install the unit. that way, In case you have gotten a defective light or you wired The blinkers backwards, you can undo it before the light is installed.

Purchased for my 2016 S1000R with 47k miles. While the plug did fit, the light didn't perform as expected even with added resistance. The plug fit but doesn't seem to function for anything except the ground/negative wire. There are only two wires in the plug, which work for both the running light and brake light, as well as the ground/negative on the OEM light. On this aftermarket light, nothing lights up with just the plug. You can get running lights if you run the red wire to a powered wire (I used the one I currently use for my accessories), but no brake lights. I'm assuming you can get brake lights but no running lights if you go to a different wire, but I need for both to work and that doesn't appear to be a possibility. The computer also doesn't like the light, even with resistors. Unfortunately I waited until after the return window had been long closed before trying to install it, so maybe I'll do a neat build sometime down the road that'll use the light instead. Seemed of reasonable quality, though certainly not the same standard as BMW branded products.All in all, I don't think this is a good option for BMW S1000R, S1000RR, or HP4 as it's listed for. The company needs to make better instructions that are vehicle specific. The current ones do not sufficiently address the question of where wires ought to plug into for full functionality. I'm confident in my ability to deal with electrical systems on bikes, but this was just too much risk with the computer not liking it.

Put this on a Harley and ask a couple people can you tell where I bought the new light and everyone thought it came from the Harley shop so it's going to be something I recommend to others

It fit. It works. It was easy to install on a 2010 FXDC. I’d buy again.

i love it on my 2015 yamaha r3

テールランプ単体としても使えたので良かったです。

これだけでは違法らしいです。夜は視認性抜群ですが、昼間は方向指示が曖昧に思います。

明るさはスモークなので想定内でしたが、若干寸法が小さいです。リアフェンダーとの隙間が気になるくらいちょっと開いてます。MOTO MPHというアメリカのメーカーで台湾製のものも持っていたことがありますが、あちらは高い分精度は高いですが、こちらは価格相応です。配線は既存のテールを外して、そのままカプラーを繋ぐだけのポン付けです。ウインカーは車検に通らなくなるのでつけていません。シートを外してリアカウルを外して、アンダーカウルを外せば交換可能です。既存テールのカプラーを車体から抜くのがちょっと面倒ですが、リアカウルとかはすぐ外れるので、特に問題はないかと。クオリティー重視ならば、もう少し価格帯を上げたほうがいいかもしれませんが、気にならない人には安価で結構見た目も変わるのでいいかもしれません。

追加で防水処理しないでくんでみた。浸水は、どうかわからないから、暫くは様子見組んだときはカウルとの隙間が少しできてしまい、その辺の精度は、価格相応といったところあとは、耐久性の心配くらい